:جديد المواضيع
النتائج 1 إلى 9 من 9

أجهزة قياس لمعدل التدفق فى السوائل

  1. #1
    عضو

    User Info Menu

    أجهزة قياس لمعدل التدفق فى السوائل

    أرجو أن تفيدونى فى مشروع تخرج عن أجهزة قياس لمعدل التدفق فى السوائل يعنى ماهى الاجهزة المطورة لقياس معدل التدفق


    0 Not allowed!

  2. #2
    عضو

    User Info Menu

    الأخ العزيز مهند عوض
    أرجو أن توضح ما تطلبه أكثر
    فهل تريد أن نوافيك بالأجهزة كمبدأ نظري أم تصميمي
    وهذا موقع ربما تجد فيه ما تريد
    http://www.howstuffwork.com


    0 Not allowed!

  3. #3
    جديد

    User Info Menu

    اريد طريقه عمل اجهزه قياس التدفق للموائع لو تكرمتوا


    0 Not allowed!

    من مواضيع خليل اباشعر :


  4. #4

  5. #5
    عضو فعال

    User Info Menu

    اخواني الاعزاء
    اؤيد الاخ مهند في تزويدنا بمعلومات عن اجهزة قياس معدل التدفق وغيرها من مواصفات ومميزات الموائع في الانابيب ومن كافة النواحي


    0 Not allowed!

  6. #6

  7. #7

  8. #8
    عضو

    User Info Menu



    Flow measurement

    In order to troubleshoot hydraulic systems and to evaluate the performance of hydraulic

    components, it is often required to measure the flow rate. For example, flow measurements are undertaken to check the volumetric efficiency of pumps and also to
    determine leakage paths within a hydraulic system
    Although, there are numerous flow measuring devices for measuring flow in a hydraulic
    circuit, this discussion is limited to the three most commonly employed, which are


    Rota meter
    Turbine flow meter and
    Orifice plate flow meter


    Rota meter

    The Rota meter also known as variable area flow meter is the most common among all
    flow measurement devices. It basically consists of a tapered glass tube calibrated with a metering float that can move vertically up and down in the glass tube

    the tube prevent the float from leaving the glass tube. Two stoppers one at the top and the other at the bottom of The fluid enters the tube through
    the inlet provided at the bottom. When no fluid is entering the tube, the float rests at the bottom of the tapered tube with one end of the float making contact with the
    lower stopper. The diameter of the float is selected in such a way that under conditions where there is no fluid entry into the tube, the float will block the small end of the tube
    completely

    When the fluid starts entering the tube through the inlet provided at the bottom, it forces the float to move upwards This upward movement of the float will continue, until an equilibrium position is reached at which point the weight of the float is balanced by the upward force exerted by the fluid on the float. Greater the flow rate, higher is the float rise in the tube. The graduated tube allows direct reading of the flow rate


    Turbine-type flow meter


    This flow meter has a turbine rotor in the housing, which is connected to the pipeline

    whose flow rate is to be measured. When the fluid flows, it causes the turbine to rotate
    Higher the flow rate, greater is the speed of the turbine. The magnetic end of a sensor
    which is positioned near the turbine blades, produces a magnetic field whose magnetic
    lines of force are interrupted by the rotation of the turbine blades, thereby generating an electrical impulse. An electrical device connected to the sensor converts the pulses to flow rate information

    Orifice plate-type flow meter

    Another method by which flow rate can be determined involves the use of an orifice

    plate-type flow meter in which an orifice is installed in the pipeline with two pressure gauges, one each on either side of the orifice. This arrangement enables us to determine the pressure drop (AP) across the orifice when the fluid flows through the pipe and given by AP = Pi- P2- The higher the flow rate, greater will be the pressure drop








    0 Not allowed!

  9. #9

الكلمات الدلالية لهذا الموضوع

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •